Notice of Receipt of Petition for Decision That Nonconforming 2006-2007 Ferrari 599 GTB Passenger Cars Manufactured Before September 1, 2007 Are Eligible for Importation |
|---|
Topics: Ferrari 599 GTB Fiorano
|
Jeffrey Giuseppe
National Highway Traffic Safety Administration
March 24, 2014
[Federal Register Volume 79, Number 56 (Monday, March 24, 2014)]
[Notices]
[Pages 16099-16101]
From the Federal Register Online via the Government Printing Office [www.gpo.gov]
[FR Doc No: 2014-06366]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
National Highway Traffic Safety Administration
[Docket No. NHTSA-2013-0109; Notice 1]
Notice of Receipt of Petition for Decision That Nonconforming
2006-2007 Ferrari 599 GTB Passenger Cars Manufactured Before September
1, 2007 Are Eligible for Importation
AGENCY: National Highway Traffic Safety Administration (NHTSA), DOT.
ACTION: Receipt of petition.
-----------------------------------------------------------------------
[[Page 16100]]
SUMMARY: This document announces receipt by the National Highway
Traffic Safety Administration (NHTSA) of a petition for a decision that
nonconforming 2006-2007 Ferrari 599 GTB passenger cars manufactured
before September 1, 2007 that were not originally manufactured to
comply with all applicable Federal Motor Vehicle Safety Standards
(FMVSS), are eligible for importation into the United States because
they are substantially similar to vehicles that were originally
manufactured for sale in the United States and that were certified by
their manufacturer as complying with the safety standards (the U.S.-
certified version of the 2006-2007 Ferrari 599 GTB manufactured before
September 1, 2007) and they are capable of being readily altered to
conform to the standards.
DATES: The closing date for comments on the petition is April 23, 2014.
ADDRESSES: Comments should refer to the docket and notice numbers above
and be submitted by any of the following methods:
Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the online instructions for submitting
comments.
Mail: Docket Management Facility: U.S. Department of
Transportation, 1200 New Jersey Avenue SE., West Building Ground Floor,
Room W12-140, Washington, DC 20590-0001.
Hand Delivery or Courier: West Building Ground Floor, Room
W12-140, 1200 New Jersey Avenue SE., between 9 a.m. and 5 p.m. ET,
Monday through Friday, except Federal holidays.
Fax: 202-493-2251.
Instructions: Comments must be written in the English language, and
be no greater than 15 pages in length, although there is no limit to
the length of necessary attachments to the comments. If comments are
submitted in hard copy form, please ensure that two copies are
provided. If you wish to receive confirmation that your comments were
received, please enclose a stamped, self-addressed postcard with the
comments. Note that all comments received will be posted without change
to http://www.regulations.gov, including any personal information
provided. Please see the Privacy Act heading below.
Privacy Act: Anyone is able to search the electronic form of all
comments received into any of our dockets by the name of the individual
submitting the comment (or signing the comment, if submitted on behalf
of an association, business, labor union, etc.). You may review DOT's
complete Privacy Act Statement in the Federal Register published on
April 11, 2000 (65 FR 19477-78).
How to Read Comments submitted to the Docket: You may read the
comments received by Docket Management at the address and times given
above. You may also view the documents from the Internet at http://www.regulations.gov. Follow the online instructions for accessing the
dockets. The docket ID number and title of this notice are shown at the
heading of this document notice. Please note that even after the
comment closing date, we will continue to file relevant information in
the Docket as it becomes available. Further, some people may submit
late comments. Accordingly, we recommend that you periodically search
the Docket for new material.
FOR FURTHER INFORMATION CONTACT: George Stevens, Office of Vehicle
Safety Compliance, NHTSA (202-366-5308).
SUPPLEMENTARY INFORMATION:
Background
Under 49 U.S.C. 30141(a)(1)(A), a motor vehicle that was not
originally manufactured to conform to all applicable FMVSS shall be
refused admission into the United States unless NHTSA has decided that
the motor vehicle is substantially similar to a motor vehicle
originally manufactured for importation into and sale in the United
States, certified under 49 U.S.C. 30115, and of the same model year as
the model of the motor vehicle to be compared, and is capable of being
readily altered to conform to all applicable FMVSS.
Petitions for eligibility decisions may be submitted by either
manufacturers or importers who have registered with NHTSA pursuant to
49 CFR Part 592. As specified in 49 CFR 593.7, NHTSA publishes notice
in the Federal Register of each petition that it receives, and affords
interested persons an opportunity to comment on the petition. At the
close of the comment period, NHTSA decides, on the basis of the
petition and any comments that it has received, whether the vehicle is
eligible for importation. The agency then publishes this decision in
the Federal Register.
J.K. Technologies, LLC of Baltimore, Maryland (Registered Importer
90-006) has petitioned NHTSA to decide whether nonconforming 2006-2007
Ferrari 599 GTB passenger cars manufactured before September 1, 2007
are eligible for importation into the United States. The vehicles which
J.K. Technologies believes are substantially similar are 2006-2007
Ferrari 599 GTB passenger cars manufactured before September 1, 2007
that were manufactured for sale in the United States and certified by
their manufacturer as conforming to all applicable FMVSS.
The petitioner claims that it compared the non-U.S. certified 2006-
2007 Ferrari 599 GTB passenger cars manufactured before September 1,
2007 to their U.S.-certified counterparts, and found the vehicles to be
substantially similar with respect to compliance with most FMVSS.
J.K. Technologies submitted information with its petition intended
to demonstrate that non-U.S. certified 2006-2007 Ferrari 599 GTB
passenger cars manufactured before September 1, 2007, as originally
manufactured, conform to many FMVSS in the same manner as their U.S.
certified counterparts, or are capable of being readily altered to
conform to those standards. Specifically, the petitioner claims that
the non-U.S. certified 2006-2007 Ferrari 599 GTB passenger cars
manufactured before September 1, 2007 are identical to their U.S.
certified counterpart with respect to compliance with Standard Nos. 102
Transmission Shift Lever Sequence, Starter Interlock, and Transmission
Braking Effect, 103 Windshield Defrosting and Defogging Systems, 104
Windshield Wiping and Washing Systems, 106 Brake Hoses, 113 Hood Latch
System, 116 Motor Vehicle Brake Fluids, 124 Accelerator Control
Systems, 126 Electronic Stability Control Systems, 135 Light Vehicle
Brake Systems, 139 New Pneumatic Radial Tires for Light Vehicles, 201
Occupant Protection in Interior Impact, 202 Head Restraints, 204
Steering Control Rearward Displacement, 205 Glazing Materials, 206 Door
Locks and Door Retention Components, 210 Seat Belt Assembly Anchorages,
212 Windshield Mounting, 216 Roof Crush Resistance, 219 Windshield Zone
Intrusion, 225 Child Restraint Anchorage Systems, and 302 Flammability
of Interior Materials.
The petitioner also contends that the non-U.S. certified vehicles
are capable of being readily altered to meet the following standards,
in the manner indicated:
Standard No. 101 Controls and Displays: replacement of the
instrument cluster with a U.S.-model component and reprogramming of the
vehicle computer.
Standard No. 108 Lamps, Reflective Devices and Associated
Equipment: replacement of the headlamps, side marker lamps, and tail
lamps with U.S.-model components and reprogramming
[[Page 16101]]
the vehicle computer to activate necessary systems.
Standard No. 110 Tire Selection and Rims for Motor Vehicles with a
GVWR of 4,536 kilograms (10,000 pounds) or Less: installation of a tire
information placard.
Standard No. 111 Rearview Mirrors: replacement of the passenger
side rearview mirror with a U.S.-model component or inscription of the
required warning statement on the face of that mirror.
Standard No. 114 Theft Protection and Rollaway Prevention:
reprogramming the vehicle computer to activate the key warning system.
Standard No. 118 Power-Operated Window, Partition, and Roof Panel
Systems: reprogramming of the vehicle computer.
Standard No. 207 Seating Systems: replacement of seating systems
with U.S.-model components to ensure compliance with FMVSS No. 207 as
well as the advanced airbag requirements of FMVSS No. 208.
Standard No. 208 Occupant Crash Protection: inspection to confirm
that labels, seat belts, airbags, sensors, control units, wiring
harnesses, knee bolsters, and braces bear part numbers of U.S.-model
components. Non-conforming parts will be replaced with U.S.-model
components. Reprograming of the vehicle computer to activate the seat
belt warning system and to assure compliance with all other applicable
requirements of the standard.
Standard No. 209 Seat Belt Assemblies: inspection of seat belts and
replacement of non-conforming belts with U.S.-model components.
Standard No. 214 Side Impact Protection: inspection of side impact
airbag systems and replacement of any non-conforming parts with U.S.-
model vehicle components.
Standard No. 301 Fuel System Integrity: inspection of all vehicles
and replacement of any non U.S.-model fuel system components with U.S.-
model components as necessary to conform to the vehicles to the
requirements of FMVSS No. 301.
Standard No. 401 Interior Trunk Release: installation of U.S.-model
interior trunk release components.
The petitioner additionally states that a vehicle identification
plate must be affixed to the vehicles near the left windshield post to
meet the requirements of 49 CFR Part 565.
Because the subject petition covers nonconforming vehicles that
have been manufactured on or after September 1, 2006, compliance with
the advanced air bag requirements of FMVSS No. 208 is of significant
concern to the agency. NHTSA is therefore particularly interested in
comments regarding the ability of a Registered Importer to readily
alter the subject vehicles to fully meet the driver and front outboard
passenger frontal crash protection and child passenger protection
requirements of FMVSS No. 208. The following is a partial listing of
the components that may be affected:
a. Driver's frontal air bag module
b. Passenger frontal air bag module
c. Passenger frontal air bag cover
d. Knee air bags
e. Knee bolsters
f. Passenger outboard frontal seat belt system
g. Driver and front outboard seat assemblies including seat tracks and
internal seat components
h. Steering wheel components, including the clock spring assembly, the
steering column, and all connecting components
i. Instrument panel
j. Instrument panel support structure (i.e. cross beam)
k. Occupant sensing and classification systems, including sensors and
processors
l. Restraint control modules
m. Passenger air bag status indicator light system, including related
display components and wiring
n. Wiring harnesses between the restraint control module, occupant
classification system and restraint system components
o. Control system computer software and firmware
All comments received before the close of business on the closing
date indicated above will be considered, and will be available for
examination in the docket at the above addresses both before and after
that date. To the extent possible, comments filed after the closing
date will also be considered. Notice of final action on the petition
will be published in the Federal Register pursuant to the authority
indicated below.
Authority: 49 U.S.C. 30141(a)(1)(A), (a)(1)(B), and (b)(1); 49
CFR 593.7; delegation of authority at 49 CFR 1.95 and 501.8.
Issued on: March 18, 2014.
Jeffrey Giuseppe,
Acting Director, Office of Vehicle Safety Compliance.
[FR Doc. 2014-06366 Filed 3-21-14; 8:45 am]
BILLING CODE 4910-59-P